Current Path : /proc/2/root/etc/sysconfig/network-scripts/

Upload File :

Current File : //proc/2/root/etc/sysconfig/network-scripts/ifdown-ipv6

#!/bin/sh
#
# ifdown-ipv6
#
#
# Taken from:
# (P) & (C) 2000-2004 by Peter Bieringer <pb@bieringer.de>
#
#  You will find more information on the initscripts-ipv6 homepage at
#   http://www.deepspace6.net/projects/initscripts-ipv6.html
#
# RHL integration assistance by Pekka Savola <pekkas@netcore.fi>
#
# Version 2005-09-22
#
# Note: if called as (like normally) by /etc/sysconfig/network-scripts/ifdown
#        exit codes aren't handled by "ifdown"
#
# Uses following information from /etc/sysconfig/network-scripts/ifcfg-$1:
#  DEVICE=<device>
#  IPV6INIT=yes|no: controls IPv6 configuration for this interface
#
# Optional for 6to4 tunneling:
#  IPV6TO4_RELAY=<IPv4 address>: IPv4 address of the remote 6to4 relay [default: 192.88.99.1]
#  IPV6TO4_ROUTING="<device>-<suffix>/<prefix length> ...": information to setup internal interfaces
#
# Optional for 6to4 tunneling links to trigger radvd:
#  IPV6_CONTROL_RADVD=yes|no: controls radvd triggering [optional]
#  IPV6_RADVD_PIDFILE=<file>: PID file of radvd for sending signals, default is "/var/run/radvd/radvd.pid" [optional]
#  IPV6_RADVD_TRIGGER_ACTION=startstop|reload|restart|SIGHUP: how to trigger radvd [optional, default is SIGHUP]
#
#  Required version of radvd to use 6to4 prefix recalculation
#   0.6.2p3 or newer supporting option "Base6to4Interface"
#  Required version of radvd to use dynamic ppp links
#   0.7.0 + fixes or newer
#


. /etc/sysconfig/network

cd /etc/sysconfig/network-scripts
. ./network-functions

CONFIG=$1
[ -f "$CONFIG" ] || CONFIG=ifcfg-$CONFIG
source_config

REALDEVICE=${DEVICE%%:*}
DEVICE=$REALDEVICE

[ -f /etc/sysconfig/network-scripts/network-functions-ipv6 ] || exit 1
. /etc/sysconfig/network-scripts/network-functions-ipv6


# IPv6 test, no module loaded, exit if system is not IPv6-ready
ipv6_test testonly || exit 0

# Test device status
ipv6_test_device_status $DEVICE
if [ $? != 0 -a $? != 11 ]; then
	# device doesn't exist or other problem occurs
	exit 1
fi

# Switch some sysctls to secure mode
/sbin/sysctl -e -w net.ipv6.conf.$SYSCTLDEVICE.forwarding=0 >/dev/null 2>&1
/sbin/sysctl -e -w net.ipv6.conf.$SYSCTLDEVICE.accept_ra=0 >/dev/null 2>&1
/sbin/sysctl -e -w net.ipv6.conf.$SYSCTLDEVICE.accept_redirects=0 >/dev/null 2>&1

# Test status of tun6to4 device
ipv6_test_device_status tun6to4
if [ $? = 0 -o $? = 11 ]; then
	# Device exists
	valid6to4config="yes"

	if [ -z "$IPV6TO4_RELAY" ]; then
		IPV6TO4_RELAY="192.88.99.1"
	fi

	# Get IPv4 address from interface
	if [ -n "$IPV6TO4_IPV4ADDR" ]; then
		# Take special configured from config file (precedence 1)
		ipv4addr="$IPV6TO4_IPV4ADDR"

		# Get IPv4 address from interface first
		ipv4addrlocal="$(ipv6_get_ipv4addr_of_device $DEVICE)"
		if [ -z "$ipv4addrlocal" ]; then
			# Take configured from config file
			ipv4addrlocal="$IPADDR"
		fi
	else
		# Get IPv4 address from interface first (has precedence 2)
		ipv4addr="$(ipv6_get_ipv4addr_of_device $DEVICE)"
		if [ -z "$ipv4addr" ]; then
			# Take configured from config file (precedence 3)
			ipv4addr="$IPADDR"
		fi
		ipv4addrlocal="$ipv4addr"
	fi

	# Get local IPv4 address of dedicated tunnel
	ipv4addr6to4local="$(ipv6_get_ipv4addr_of_tunnel tun6to4 local)"

	if [ -z "$ipv4addrlocal" -o -z "$ipv4addr6to4local" ]; then
		# no IPv4 addresses given, 6to4 sure not configured
		valid6to4config="no"
	else
		# Check against configured 6to4 tunnel to see if this interface was used before
		if [ "$ipv4addrlocal" != "$ipv4addr6to4local" ]; then
			# IPv4 address of interface does't match local tunnel address, interface was not used for current 6to4 setup
			valid6to4config="no"
		fi
	fi

fi

# Shutdown of 6to4, if configured
if [ "$valid6to4config" = "yes" ]; then
	if [ -n "$IPV6TO4_ROUTING" ]; then
		# Delete routes to local networks
		for devsuf in $IPV6TO4_ROUTING; do
			dev="$(echo $devsuf | awk -F- '{ print $1 }')"
			ipv6_cleanup_6to4_device $dev
		done
	fi

	# Delete all configured 6to4 address
	ipv6_cleanup_6to4_tunnels tun6to4

	# Control running radvd
	ipv6_trigger_radvd down "$IPV6_RADVD_TRIGGER_ACTION" $IPV6_RADVD_PIDFILE
fi

# Delete all current configured IPv6 addresses on this interface
ipv6_cleanup_device $DEVICE

Copyright 2K16 - 2K18 Indonesian Hacker Rulez