| Current Path : /proc/self/root/proc/2/root/proc/2/root/usr/share/doc/sed-4.2.1/ |
| Current File : //proc/self/root/proc/2/root/proc/2/root/usr/share/doc/sed-4.2.1/BUGS |
* ABOUT BUGS Before reporting a bug, please check the list of known bugs and the list of oft-reported non-bugs (below). Bugs and comments may be sent to bonzini@gnu.org; please include in the Subject: header the first line of the output of ``sed --version''. Please do not send a bug report like this: [while building frobme-1.3.4] $ configure sed: file sedscr line 1: Unknown option to 's' If sed doesn't configure your favorite package, take a few extra minutes to identify the specific problem and make a stand-alone test case. A stand-alone test case includes all the data necessary to perform the test, and the specific invocation of sed that causes the problem. The smaller a stand-alone test case is, the better. A test case should not involve something as far removed from sed as ``try to configure frobme-1.3.4''. Yes, that is in principle enough information to look for the bug, but that is not a very practical prospect. * NON-BUGS `N' command on the last line Most versions of sed exit without printing anything when the `N' command is issued on the last line of a file. GNU sed instead prints pattern space before exiting unless of course the `-n' command switch has been specified. More information on the reason behind this choice can be found in the Info manual. regex syntax clashes (problems with backslashes) sed uses the Posix basic regular expression syntax. According to the standard, the meaning of some escape sequences is undefined in this syntax; notable in the case of GNU sed are `\|', `\+', `\?', `\`', `\'', `\<', `\>', `\b', `\B', `\w', and `\W'. As in all GNU programs that use Posix basic regular expressions, sed interprets these escape sequences as meta-characters. So, `x\+' matches one or more occurrences of `x'. `abc\|def' matches either `abc' or `def'. This syntax may cause problems when running scripts written for other seds. Some sed programs have been written with the assumption that `\|' and `\+' match the literal characters `|' and `+'. Such scripts must be modified by removing the spurious backslashes if they are to be used with recent versions of sed (not only GNU sed). On the other hand, some scripts use `s|abc\|def||g' to remove occurrences of _either_ `abc' or `def'. While this worked until sed 4.0.x, newer versions interpret this as removing the string `abc|def'. This is again undefined behavior according to POSIX, but this interpretation is arguably more robust: the older one, for example, required that the regex matcher parsed `\/' as `/' in the common case of escaping a slash, which is again undefined behavior; the new behavior avoids this, and this is good because the regex matcher is only partially under our control. In addition, GNU sed supports several escape characters (some of which are multi-character) to insert non-printable characters in scripts (`\a', `\c', `\d', `\o', `\r', `\t', `\v', `\x'). These can cause similar problems with scripts written for other seds. -i clobbers read-only files In short, `sed d -i' will let one delete the contents of a read-only file, and in general the `-i' option will let one clobber protected files. This is not a bug, but rather a consequence of how the Unix filesystem works. The permissions on a file say what can happen to the data in that file, while the permissions on a directory say what can happen to the list of files in that directory. `sed -i' will not ever open for writing a file that is already on disk, rather, it will work on a temporary file that is finally renamed to the original name: if you rename or delete files, you're actually modifying the contents of the directory, so the operation depends on the permissions of the directory, not of the file). For this same reason, sed will not let one use `-i' on a writeable file in a read-only directory, and will break hard or symbolic links when `-i' is used on such a file. `0a' does not work (gives an error) There is no line 0. 0 is a special address that is only used to treat addresses like `0,/RE/' as active when the script starts: if you write `1,/abc/d' and the first line includes the word `abc', then that match would be ignored because address ranges must span at least two lines (barring the end of the file); but what you probably wanted is to delete every line up to the first one including `abc', and this is obtained with `0,/abc/d'. `[a-z]' is case insensitive `s/.*//' does not clear pattern space You are encountering problems with locales. POSIX mandates that `[a-z]' uses the current locale's collation order -- in C parlance, that means strcoll(3) instead of strcmp(3). Some locales have a case insensitive strcoll, others don't. Another problem is that [a-z] tries to use collation symbols. This only happens if you are on the GNU system, using GNU libc's regular expression matcher instead of compiling the one supplied with GNU sed. In a Danish locale, for example, the regular expression `^[a-z]$' matches the string `aa', because `aa' is a single collating symbol that comes after `a' and before `b'; `ll' behaves similarly in Spanish locales, or `ij' in Dutch locales. Another common localization-related problem happens if your input stream includes invalid multibyte sequences. POSIX mandates that such sequences are _not_ matched by `.', so that `s/.*//' will not clear pattern space as you would expect. In fact, there is no way to clear sed's buffers in the middle of the script in most multibyte locales (including UTF-8 locales). For this reason, GNU sed provides a `z' command (for `zap') as an extension. However, to work around both of these problems, which may cause bugs in shell scripts, you can set the LC_ALL environment variable to `C', or set the locale on a more fine-grained basis with the other LC_* environment variables.
Copyright 2K16 - 2K18 Indonesian Hacker Rulez
;?>)